![]() Please see last page of the manual if your Plasma or LCD needs extension arms. **PLEASE NOTE: You will not use all of the hardware included. *Bag 7 only included with models FT65-03, FT65B-CC, LM65FT and DC65FT If you feel resistance, remove the bolt immediately! Next determine the correct length of the required bolt as described in the following step. Thread the bolts carefully into your LCD or plasma by hand to determine which provided mount hardware (correct diameter) is appropriate for installation. Plasma: CAUTION: Select Bag 1-4, which most resem- bles the hole side on the back of your LCD/Plasma. Selecting the Appropriate Hardware for your LCD/ Do not screw too tight until all the screws are in.ĭrive the 2nd screw into the opposite upper right hand mounting hole of the Wall Plate, then proceed to drive the remaining 4 screws into the concrete anchors as seen in figure 2. Wall, screw 1 Dry Wall Screw and 1 Dry Wall Washer (P & Q) in the upper left mounting hole of the Wall Plate. Once the Wall Plate is in the correct position on the Insert the anchors into the holes and set them flush to the wall by tapping them in with a hammer (Figure 6). Drill into the wall at least as deep as the screw is long (3 inches). Drill holes for the concrete anchors using an electric drill with a masonry bit (1/2’’ or 12mm (Figure 5). Utilize the built-in bubble level to ensure proper mounting (Figure 3). Mark the six holes you will be using for concrete anchors (Figure 4). Plate at the height you want to install the Plasma/LCD wall Mount. Attaching Wall Mount to concretel: Place the Wall NOTE: Due to the weight of the LCD/Plasma TV’s, it is necessary to mount the Wall Plate to at least 2 studs.Īttaching Wall Plate to Concrete: 1b. Now tighten both screws, proceed to drive the remaining 2 screws into the studs as seen in figure 2, page 1. Using the Bubble Level as your guide (Figure 3, page 2), drive the 2nd screw into the opposite upper right hand mounting hole of the Wall Plate. Drill pilot hole with 1/8 inch drill bit. Do not screw too tight until after all the screws are in. The tilt arms will adjust horizontally to the right and left up to 8 inches after you determine the desired viewing location.Īttaching LevelMount to wall: Once the Wall Plate is in the correct position on the studs, screw 1 Hex Screw and 1 Hex Washer (P & Q) in the upper left mounting hole of the Wall Plate into the stud. The mount requires a minimum of two studs to ensure proper and safe installation. Using the included stud finder (Figure 1) It is recom- mended that the center of the stud be used – and that a nail be used to verify that a stud has been located. Locate wall studs: Locate a proper place to mount by Make sure all screws and bolts are tightened before allowing Wall Mount to bear the full weight of the LCD Display.Īttaching Wall Plate to Wooden Studs: 1a. Before installing, check to make sure all parts of the mount are included. PLEASE NOTE: THE MOUNT MUST BE ATTACHED TO WOOD STUDS OR TO PROPERLY INSTALLED ANCHORS IN CONCRETE. It is the responsibility of the installer to verify that the mount is anchored properly to the wall. Tools required for attachment to stud: 1/2’’ (12mm) Socket Wrench Stud finder Tools required for attaching to concrete: Electric drill 1/2’’ (12mm) Masonry BitĬAUTION: Installer must make sure the LCD Wall Mount is proper- ly and securely attached and that appropriate fasteners are used. V M5 x 48 Bolt 8 7* W M5 Hex Nut 8 X M5 Washer 8 Y L-Shape Bar Lock 2 8 Z Phillips screws M5 x 10 Bolt 4 AA M5 Hex Nut 2 BB M5 Butterfly Nut Please also visit our Web Site at for assistance. ![]() ![]() Our trained Customer Service Department is open 24 hours a day, 7 days a week, every day of the year and is prepared to assist you in both English and Spanish. DO NOT RETURN THIS PRODUCT TO THE STORE OR WEB SITE YOU PURCHASED IT FROM! IF YOU BELIEVE THIS MOUNT IS DEFECTIVE, HAS MISSING OR BROKEN PARTS, OR IF YOU ARE HAVING DIFFICULTY INSTALLING THIS MOUNT TO YOUR WALL OR FITTING YOUR TV, PLEASE CONTACT OUR COMPANY, LEVEL MOUNT, DIRECTLY.ĭial 1 8 or email us at any time of the day or night for a quick and efficient solution to your problem.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |